Mold design and precision are the starting point for creating smooth inner walls
The design philosophy and surface condition of the mandrel-which directly contacts and shapes the inner wall of the tube-are of critical importance. A mandrel that has been precision-polished to a mirror-like finish is a prerequisite for achieving a smooth inner wall; even the slightest scratch, machining mark, or carbon buildup will be directly replicated on the tube's inner wall like a "fingerprint." Modern high-end molds take this a step further by employing core-ring sleeve technology. By adding a floating sleeve made of a special material to the core, the inner wall-which has not yet fully cooled-undergoes secondary extrusion and polishing during the extrusion process. This effectively eliminates microscopic ripples caused by melt fracture or uneven flow, significantly improving the smoothness of the inner wall. At the same time, the smoothness of the geometric design of the entire mold runner system directly affects the stability of melt flow. Any dead corners or abrupt structural changes can cause melt stagnation and decomposition, ultimately resulting in char particles or black spots on the inner wall.
Precise control of process parameters is key to ensuring a smooth surface
Temperature settings are among the most critical factors, particularly the temperature of the core die. If the temperature is too low, the PE raw material cannot obtain sufficient heat to fully plasticize, and unmelted particles will form microscopic roughness on the inner wall; if the temperature is too high, it may cause thermal oxidation and degradation of the raw material, resulting in bubbles or char. The ideal temperature must be precisely maintained within the critical range between material melting and thermal decomposition, with a reasonable temperature gradient distribution along the mold axis. The stability of both the extrusion speed and the haul-off speed is equally critical; fluctuations in either will cause dynamic changes in the pipe wall thickness, and these periodic fluctuations will create visible ripples on the inner wall. Furthermore, melt pressure must be maintained within an appropriate range; insufficient pressure results in inadequate melt density, while excessive pressure may cause melt rupture, both of which compromise the smoothness of the inner wall.
The quality of raw materials and the drying process are fundamental factors affecting the cleanliness of the inner walls.
The moisture content of the PE raw material directly determines the severity of pitting on the inner wall. When raw material with excessive moisture content is extruded at high temperatures, the moisture instantly vaporizes to form bubbles; as these bubbles burst near the inner wall surface, they leave behind a dense network of pits. Many quality issues stem precisely from improper raw material storage or neglect of the drying process. Additionally, the melt flow rate and molecular weight distribution of the raw material affect processing performance. Materials with excessively high flow rates are prone to turbulence within the mold, while those with excessively low flow rates require higher processing temperatures; both factors make it more difficult to achieve a smooth inner wall. If recycled materials are used, impurities, gels, or degradation products they may contain can directly contaminate the inner wall surface.
The proper configuration of the cooling and shaping system is key to achieving a smooth cured surface
After the molten PE pipe parison exits the mold, it must be rapidly cooled and shaped using a sizing sleeve and a cooling water tank. The structural design of the sizing sleeve-particularly the distribution of the cooling water channels and the uniformity of vacuum suction-determines whether the pipe will deform during the cooling process. If cooling water strikes the pipe surface directly, it can cause localized cooling inconsistencies, generating internal stresses that lead to irregular deformation of the inner wall. Ideal cooling should be uniform and gradual, allowing the pipe to cool steadily from the outer wall toward the inner wall, thereby fully "freezing" the smooth inner wall profile imparted by the mold. Control of water temperature is also critical; excessively cold cooling water can cause intense heat exchange, which may easily result in microcracks or stress marks on the inner wall of the pipe.
The overall performance and maintenance condition of the equipment are key to ensuring the long-term, stable production of smooth-walled tubes.
The plasticizing capacity of the extruder determines the uniformity of the melt. If plasticization is insufficient or mixing is uneven, resulting in unmelted "fish eyes" or variations in composition within the melt, localized defects will form on the inner wall. The stability of the haul-off unit directly affects the consistency of wall thickness; any slippage or fluctuations in speed will compromise the smoothness of the inner wall. Furthermore, regular equipment maintenance is essential. Carbon buildup gradually forming inside the die, wear on the die gap, and temperature drift caused by aging heating elements will all gradually erode the quality of the inner wall over time, causing defects to gradually appear on the originally smooth pipe surface.
