Blog

Safety and Security of HDPE Pipe Offset Production Lines

Mar 19, 2026 Leave a message

I. Safety Operating Procedures

1. Startup and Shutdown Safety:

Pre-startup inspection: Before starting the machine, verify that all heating zones have reached the set temperature and have been maintained at that temperature for a period of time (typically 30–45 minutes). Ensure that the material inside the barrel is completely melted before starting the main screw. Cold starts are strictly prohibited, as they may cause the screw to break or result in severe wear to the barrel.

Shutdown Procedure: Before shutting down, the plastic inside the screw must be completely purged (i.e., switch to cleaning material or run the screw idle until empty) to prevent the material from decomposing and carbonizing inside the high-temperature barrel after shutdown, which could cause mold blockages or black spots during the next startup.

Warning Signs: Audible and visual alarms must be activated before starting the equipment to ensure that no personnel are present in the vicinity of the haul-off unit, cutter, or other surrounding equipment.

2. High-Temperature Protection:

The barrel, die, and flanges on the production line reach temperatures as high as 200–250°C, so heat shields or protective barriers must be installed. Operators must wear heat-resistant gloves and face shields when cleaning the die head to prevent burns from molten plastic splashes.

3. Mechanical Guarding:

All moving parts (motor couplings, pulleys, and gearbox input shafts) must be equipped with secure guards.

There is a risk of entrapment with the traction machine; under no circumstances should you touch the tracks or belts while the machine is in operation. When adjusting the opening and closing of the traction machine, ensure that your hands are kept well away from potential pinch points.

4. Electrical Safety:

Ensure that grounding wires are secure to prevent the buildup of static electricity. Routinely check the terminals of the variable frequency drive and heating contactors for looseness to prevent fires caused by overheating due to poor contact.

5. Emergency Procedures:

If equipment jams or material leaks occur, press the emergency stop button immediately. When clearing material buildup from the die head, use a brass tool to avoid damaging the die surf.

 

II. Daily and Routine Maintenance

1. Maintenance of the Extruder Main Unit (Top Priority)

Gearbox (Reduction Gearbox): Check the oil level sight glass daily to ensure the oil level is above the mid-mark. Replace the lubricating oil after the first 300 hours of operation, and thereafter every 3,000–4,000 hours of operation or once a year. Use high-quality extreme-pressure gear oil.

Screw and Barrel: Heat strictly according to process temperatures to prevent the screw from breaking due to excessive torque. Inspect the screw for wear regularly (e.g., every 3 months) by measuring the outer diameter. If output decreases significantly or melt backflow occurs, consider repairing or replacing the screw.

Cooling System: Check that the barrel cooling fan (or water-cooled solenoid valve) is operating normally to prevent uncontrolled barrel temperatures that could cause material decomposition.

2. Maintenance of the Vacuum Sizing Tank

Water Supply and Nozzles: HDPE production typically uses recirculating water. It is necessary to regularly remove scale and impurities from the vacuum tank and water tank, particularly from the spray nozzles, as blockages can lead to uneven cooling of the pipe and deviations in roundness. It is recommended to inspect and clear the nozzles weekly.

Vacuum Pump: Check the water level and circulation water temperature of the vacuum pump, and ensure the bearings remain lubricated. Regularly clean the filter screen at the vacuum pump inlet to prevent debris from clogging the piping.

3. Maintenance of the Haul-off and Cutting Machines

Haul-off Tracks/Belts: Regularly check that the clamping pressure on the haul-off is uniform to prevent the pipe from slipping. For rubber tracks, prevent oil contamination to avoid rubber aging and slippage.

Cutting Machine: Inspect the wear on the saw blades of the planetary cutting machine (used for large-diameter pipes) and ensure the clamping mechanism is synchronized. Regularly apply grease to the linear guides and bearings to ensure smooth movement of the cutting carriage.

4. Maintenance of Electrical Components and Sensors

Regularly clean dust from inside the control cabinet (using compressed air; ensure the power is turned off before proceeding) to prevent dust from causing short circuits on the circuit boards.

Check that the thermocouples (temperature probes) are securely connected and that the shielding wires are not damaged. Inaccurate temperature readings are a direct cause of yellowing on the inner walls of HDPE pipes or poor plasticization.

 

We recommend establishing a maintenance log for the production line to record the dates of each lubricant change, screw cleaning, and bearing replacement, thereby creating a traceable preventive maintenance system. This is essential to ensure the long-term, efficient, and stable operation of the HDPE pipe production line.

Send Inquiry