Common ABS Sheet Production Problems and Solutions
Many processors buy brand-new ABS sheet extrusion lines, yet still run into quality troubles during trial production. New machines do not automatically guarantee perfect sheets. Most early defects come from incorrect commissioning, raw material handling, parameter mismatch or roll calibration.
1. Silver streaks & tiny bubbles on sheet surface
✅ Symptoms: Silvery lines, scattered bubbles, cloudy surface, easy to show up at startup of new equipment
- Main causes: ABS absorbs moisture easily; insufficient drying; poor vacuum venting; local overheating leads to material decomposition
- Solutions
- Dry ABS pellets at 80–85℃ for 3–4 hours before feeding
- Check vacuum system of the new extruder, keep stable negative pressure
- Slightly lower temperature of the front barrel and die zone
- Purge the barrel and die thoroughly before formal trial run
2. Uneven sheet thickness, thickness drifting
✅ Symptoms: One side thicker, thickness changes up and down, hard to reach tolerance
- Main causes: Die gap not balanced after installation; chill rolls not parallel; unstable feeding speed; melt pressure fluctuation
- Solutions
- Re-calibrate die lip gap on the new die head
- Adjust parallelism and gap of three-roll calender
- Use steady volumetric or gravimetric feeder, avoid material bridging in hopper
- Keep extruder speed and haul-off speed synchronized
3. Sheet warping, curling after cutting
✅ Symptoms: Sheet bends upward or downward, not flat, brings trouble for thermoforming
- Main causes: Unbalanced cooling temperature between top and bottom chill rolls; residual internal stress; mismatched haul-off tension
- Solutions
- Balance temperature of upper and lower cooling rolls
- Reduce excessive pulling tension; match haul-off speed with extrusion output
- Slow down cooling speed properly for thick ABS sheet
- Add annealing station if high flatness is required for thermoforming grade
4. Die lines / longitudinal scratches on sheet surface
✅ Symptoms: Continuous thin lines along extrusion direction
- Main causes: Die lip has burrs or residual impurities; dirty screen pack; foreign particles stuck on roll surface
- Solutions
- Polish die lip carefully after first commissioning of new line
- Replace screen pack regularly, select proper mesh combination
- Keep chill roll surface clean, protect rolls from scratch during commissioning
- Filter raw material and avoid mixed contaminated regrind
5. Matte spot, orange peel & poor gloss consistency
✅ Symptoms: Gloss differs across the sheet, rough orange-peel texture
- Main causes: Melt plasticization incomplete; roll surface temperature unstable; roll surface not fully contacting sheet
- Solutions
- Optimize barrel temperature profile to get uniform plasticizing
- Control chill roll temperature steadily
- Adjust roll pressure to ensure full contact between sheet and roll surface
- Confirm you use the correct ABS grade (high-gloss / matte)
6. Black specks & burnt marks
✅ Symptoms: Small black dots, burnt brown marks
- Main causes: Dead corner inside new die or adapter; local over-shearing; long residence time; contaminated raw materials
- Solutions
- Fully purge new extrusion line before production
- Do not set too high temperature or too high backpressure
- Check flow channel design, eliminate dead zones
- Control regrind ratio and avoid degraded recycled material
New equipment commissioning needs a stable running plan. Do not push maximum speed at the very beginning. Start with low speed, check vacuum, feeding, roll calibration and sheet quality step by step. Once parameters are locked, then raise production speed gradually. This can avoid most startup defects and protect your brand-new screw, die and calender rolls.
FAQ
Q: My new ABS sheet line keeps producing silver marks, is the machine defective?
A: In most cases it is a drying or vacuum problem, not machine quality. Check raw material moisture first.
Q: How to get stable flat ABS sheet for thermoforming?
A: Focus on balanced cooling, synchronized haul-off speed and proper drying; reduce residual stress.
Hot Tags: pe/pp/abs/ps/pmma/asa/hips mono or multi layer sheet/board/plate production line, China pe/pp/abs/ps/pmma/asa/hips mono or multi layer sheet/board/plate production line manufacturers, suppliers, factory, PVC Wave Roof Sheet Production Line, PMMA Sheet Production Line, plastic board extrusion line, PE Sheet Extrusion Line, PMMA Transparent Sheet Production Line, plastic sheet production line
